DAMA H7 Male Wire Harness - Connector for Headlight 9" 18AWG | Pack of 2

DAMA H7 Male Wire Harness - Connector for Headlight 9" 18AWG | Pack of 2

Repair, extend, or adapt compatible H7 lighting circuits cleanly with the DAMA H7 Male Wire Harness Pack from HID Concept.com. This adapter harness is engineered for custom automotive installations where an H7 male connection interface is required for compatible wiring projects or custom auxiliary hardware. Each pigtail lead features 9 inches of 18AWG insulated wire, offering a reliable path for integrating aftermarket HID Xenon ballasts, custom LED conversion kits, or external driver modules without permanent wire splices. Delivered as a matching set of two, these pre-wired pigtails can be used in compatible wiring repairs or custom connector replacement projects for brittle or corroded terminal connections.

Key Features & Benefits

• H7 Male Connection Interface: Designed with precise H7 male blade terminals to plug into standard vehicle factory H7 female power sockets.
• 9-Inch Wiring Extension: Provides a practical 9-inch wire length to easily clear tight housing spaces and route custom electrical paths.
• 18AWG Insulated Wire: Constructed from standard 18AWG electrical wire strands wrapped in an insulated wire jacket to provide electrical continuity for compatible automotive circuits.
• Functional Repair Alternative: Provides an alternative to custom spade-terminal wiring, maintaining a clean configuration interface.
• Convenient Pack of 2: Includes a matching pair of male pigtail assemblies to complete both the passenger and driver-side headlight updates simultaneously.

Vehicle Compatibility & Applications

This H7 male pigtail harness is a servicing accessory engineered for applications using H7-style connectors across headlight or compatible fog light applications.

Compatibility Note

Always verify your vehicle's factory plug configuration and accessory requirements before starting installation. These components feature exposed H7 male blade terminals on a molded terminal block rather than a latching female bulb socket. They are commonly used in aftermarket HID and LED wiring projects where custom drivers lack a direct factory connection interface. This harness is not intended for direct plug-in use into OEM factory HID ballasts unless structural compatibility has been confirmed. Because individual trim configurations vary, always check your factory harness layout before ordering.

Performance & Visibility Section

When performing a custom conversion or headlight wiring repair, achieving solid connector engagement is critical for maintaining electrical continuity. Loose wire splices or exposed pins can cause excessive electrical resistance, which may contribute to voltage loss or intermittent lighting operation while driving. Integrating the DAMA H7 male pigtail harness establishes a compatible connector interface that provides electrical continuity between your factory plug and your auxiliary components. Because this passive wire accessory acts strictly as an electrical conductor rather than an active light source, it does not alter the beam pattern, color temperature, or lumen output of your lights; instead, it provides electrical continuity through a compatible connector so your components can receive power as engineered.

OEM Quality & Reliability Section

DAMA automotive lighting accessories provide functional, durable aftermarket servicing parts for seamless project integration. Built with standard 18AWG insulated wire, molded connector housings, and precisely secured metal terminal blades, these pigtails are suitable for typical automotive wiring applications. This matching 2-pack delivers an organized wiring solution as an alternative to custom wiring modifications or uninsulated open pins, ensuring a clean installation during routine maintenance or custom headlight builds.

Installation Information

This H7 pigtail set features a straightforward, non-destructive wiring architecture. Turn off the vehicle's ignition and ensure all headlight switches are completely unpowered before starting work. Access the factory H7 connector according to your headlight manufacturer's service procedure. Insert the H7 male blade terminals of the DAMA adapter fully into your vehicle's factory H7 power receiving socket until properly seated. Splice, crimp, or solder the open-ended pigtail wires directly to the input lines of your aftermarket HID ballast, LED driver, or custom controller module. Seal all customized wire joins using automotive heat-shrink tubing or premium electrical tape, and secure line slack cleanly, clear of hot engine components or moving parts.

Technical Warning: Ensure the vehicle's electrical circuit is completely dead before modifying lines. Always check and verify correct electrical polarity (positive and negative wire paths) between your vehicle's factory loom and your aftermarket equipment before applying power to avoid blowing fuses or damaging sensitive electronic modules.

Technical Specs