DAMA AL 7317408 D1S D3S HID Ballast Power Plug Connector Wire Harness for Xenon Headlight Bulb to Ballast 11" 18AWG | Pack of 1

DAMA AL 7317408 D1S D3S HID Ballast Power Plug Connector Wire Harness for Xenon Headlight Bulb to Ballast 11" 18AWG | Pack of 1

Repair damaged factory lighting paths with the DAMA AL 7317408 HID Ballast Wire Harness Set from HID Concept.com. This 2-wire replacement kit is configured to interface with headlight systems utilizing the AL Bosch 130732931201 Headlight Control Module. The set includes an 11-inch 18AWG main power input lead to link the ballast directly to your vehicle's 12V power source, alongside a dedicated ballast-to-bulb output cable. Both lines terminate at a molded plastic sealing cap designed to plug tightly into the ballast terminal ports, shielding the electrical contacts from direct exposure inside the headlight housing assembly.

Key Features & Benefits

• 130732931201 Fitment Layout: Configured to match the terminal tracking and socket layout of the AL Bosch 130732931201 HID Xenon control module.
• Integrated Plastic Sealing Cap: Features a molded protective plastic cap that seats tightly into the socket interfaces to shield connections from debris.
• Dual-Cable Replacement Loop: Provides a multi-point wiring repair path, featuring a main power vehicle input line on one end and a ballast-to-bulb connection line on the other.
• 18AWG Insulated Wiring: Built with 11 inches of 18AWG insulated wiring designed to deliver line slack within deep headlight housings.
• Complete Wire Set: A complete wire set for the Al Bosch OEM ballast or OE-PART 130732931201 HID Xenon ballasts.

   

Vehicle Compatibility & Applications

This dual-wire repair harness set is engineered to service factory 35W D1S, D1R, D3S, and D3R xenon lighting systems driven by compatible AL Bosch ballast modules.

Compatibility Note

Confirm your vehicle's factory ballast part number before ordering. This wire set is compatible with vehicles that utilize the AL Bosch 130732931201 ballast, which may include certain model years of the BMW 3 Series, Mercedes-Benz C-Class, Jeep Cherokee, Chevrolet Camaro, Hyundai Santa Fe, and other OEM HID-equipped models. Because different trim levels and options affect factory component packaging, compatibility depends on the vehicle actually having this exact module footprint installed. Always pull your headlight housing to physically verify the "130732931201" ballast part number on your vehicle before ordering.

Performance & Visibility Section

Xenon high-intensity discharge systems depend on steady current delivery to maintain proper illumination. When factory wiring clips degrade from aging or wear, loose connections can limit power to the control module, causing headlight flickering, delayed ignitions, or intermittent dropouts that alter your nighttime driving visibility. Integrating this dual-wire DAMA harness set allows you to replace loose or worn wiring paths by renewing both the primary input loop and the bulb output signal line under a secure plastic cap interface. Because these wires act as a passive conductor path rather than a light-emitting source, they do not independently change the color temperature, raw lumens, or beam pattern of your headlights; instead, they help maintain the electrical connection necessary for your factory projector headlights to operate as intended.

OEM Quality & Reliability Section

DAMA automotive lighting hardware provides functional aftermarket servicing solutions designed to address electrical wear points without requiring the purchase of an entirely new headlight housing assembly. This dual-wire harness set incorporates thick insulation, secure terminal contacts, and a tight-fitting plastic cap interface built to match standard replacement needs. It delivers a direct-fit structural alternative to support your factory lighting systems during vehicle maintenance.

Installation Information

This repair harness kit requires manual integration into the vehicle’s headlight circuit. Disconnect the vehicle's battery completely before beginning any electrical work. Unplug the existing wire set and remove the old plastic cap from the ballast housing ports. Mount the new DAMA integrated plastic sealing cap firmly into the ballast socket until it is tightly seated. Route the bulb connector line directly to your HID bulb base, and use a multimeter to verify the positive and ground paths of your factory power feed before splicing the 11-inch input pigtail. Ensure all manual wire splices are fully insulated using heat-shrink tubing or high-grade electrical tape.

Technical Warning: Ensure the vehicle's ignition is completely off, and forward lighting systems are unpowered before performing maintenance. Because xenon headlight systems generate high-voltage currents downstream from the control module, never alter or touch the bulb-side wiring while the vehicle circuits are active.