DAMA 194 T10 Female Wire Harness - Socket Connector for Interior/Parking/Side Marker Lights 4.5" 18AWG | Pack of 2

DAMA 194 T10 Female Wire Harness - Socket Connector for Interior/Parking/Side Marker Lights 4.5" 18AWG | Pack of 2

Replace worn, damaged, or corroded 194/T10 bulb sockets with DAMA 194 T10 Female Wire Harnesses. This pack of 2 replacement pigtail sockets is designed for interior, parking, side marker, license plate, and other low-wattage auxiliary lighting applications using compatible 194/T10, 168, 2825, or W5W wedge bulbs. Each harness features 18AWG copper wire, approximately 4.5 inches of lead length, and open-ended pigtail leads for splicing, crimping, or soldering into an existing wiring loom. This passive socket connector helps restore reliable electrical contact but does not change circuit voltage or eliminate CANbus warnings.

Key Features & Benefits

• Durable Socket Construction: Built with a durable T10 / 194 female wedge-style socket head designed to replace worn, damaged, corroded, or heat-affected factory socket housings.
• Dual-Lead Copper Wire System: Constructed with 18AWG copper wire to support reliable and consistent electrical flow for single-circuit miniature automotive lamps.
• Replacement Repair Component: Serves as a practical hardware solution to address intermittent lighting issues, corrosion, or loose bulb fitment caused by worn original factory socket contacts.
• Halogen & LED Bulb Support: Designed to accept compatible T10 wedge-base bulbs, maintaining steady electrical contact for standard glass wedge filaments and compatible aftermarket LED replacements.
• Wedge Base Interoperability: Accommodates common miniature wedge bulb trade sizes matching T10 and W2.1x9.5d footprint dimensions, such as 194, 168, 2825, W5W, 147, 152, 159, 161, 175, 194NA, 194ST, 194LL, 168NA, 2821, and 2827.

Vehicle Compatibility & Applications

This pigtail connector is compatible with automotive, trailer, motorcycle, and RV applications that utilize a standard T10 / 194 / W5W miniature wedge bulb socket configuration. It serves as a replacement hardware component for secondary exterior and interior illumination paths.

Common single-circuit application areas include:

• Instrument panel clusters, dashboard backlighting, and interior gauge pods
• License plate light housings, interior dome lights, map lights, and stepwell convenience lighting
• Side marker light housings, clearance indicators, and front parking lamp assemblies
• Auxiliary trunk lighting, glove box illumination, and RV interior accent lights

Disclaimer: Because locking tab configurations, twist-lock depths, and vehicle-specific harness lengths vary significantly across automotive manufacturers, always visually check your original factory socket configuration against this replacement design before installing. This hardware component does not alter overall circuit resistance; auxiliary load resistors or CANbus-adapted bulbs remain necessary to help prevent dashboard error notifications on sensitive vehicle monitoring platforms.

Performance & Visibility Section

Replacing a cracked, corroded, or damaged factory receptacle with this replacement pigtail helps restore electrical contact across your accessory lighting lines. While a replacement socket harness does not independently generate light or alter overall vehicle voltage, establishing clean metal-to-base physical contact helps your installed incandescent or LED bulbs operate under normal circuit conditions. This supports intended light projection, clarity, and signal visibility across side markers, license plate lighting, and dashboard gauges.

OEM Quality & Reliability Section

The DAMA T10 socket uses structured dimensions to help ensure proper alignment when installed into matching lamp housings. This aftermarket pigtail component features insulated wire leads and internal metal terminal clips configured to match standard T10 wedge bulb bases. Its compact socket design helps keep miniature accessory lamps positioned properly within their respective housings while supporting reliable electrical contact during normal use.

Installation Information

This replacement wire harness is supplied with open-ended pigtail wire leads to accommodate standard automotive splicing, crimping, or soldering into an existing electrical wiring loom. Since this is a simple 2-wire single-circuit component handling positive feed and negative ground, installation is straightforward. However, because wire color codes can vary from your vehicle's factory wiring schematic, it is recommended to verify the positive and ground leads using a digital multimeter or test light prior to making permanent connections to ensure proper circuit mapping.